Process: Make Piezo one/two/three-channel electronics to piezo order starting 2013-11-12 ending 2014-01-04

If you were logged in and working on this process, you would log your work on this page.

Outputs

Scheduled:

Unplanned Production:

Work

Planned Work: (Requirements are ordered by due date)

R&d electronics work: 50.00 Time - Hours due Aug. 20, 2013

03/02/2014
3-Axis piezo driver assembled and working.
The driver is on operation with the piezo stack and the piezo tube for 1h for test. The metallic enclosure is warm, but just a little, nothing to be aware.
https://drive.google.com/file/d/0B_KN6G919YgnWXlmNGtPWnM1Vm8

31/01/2014
New components added to the part list.

30/01/2014
Re-assembling a 3-Axis driver using the new PCB and updating the part list with the missing components
https://docs.google.com/spreadsheet/ccc?key=0AvKN6G919YgndElQenVpbUZ6UTk1N0liYm4zbGRKbkE&usp=drive_web#gid=5

15/01/2014
Connectorizing the 3-axis piezo finger. Instructions here: https://docs.google.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY

Proceeding tests, The electronic system is working well, but the frequency limit is lower than we've supposed (about 25Hz using the filtered output, accordint to the datasheet we expect 3x this frequency using the non-filtered output).
The fiber is moving on the Z-axis, but we have a XY component working at the same time. I think this is due the bad quality of the actual mechanics and the non uniformity of the springs. I've also found a mistake at the top_base, it should the rotated by 45 degrees to be aligned with the XY-axis!

07/01/2014
Proceeding a heating test on the 3-axis PDm200: (https://docs.google.com/spreadsheet/ccc?key=0AvKN6G919YgndEEyamtKX1ZFU0Zkb1pIUTdFS2hybWc&usp=drive_web#gid=4)

1) no external dissipation, box closed, sensor on the black heat sink, measuring each 5min
2) Using the thermal pad with adhesive (H48-6G-20-20-2.6-1A) and NO thermal paste connecting the PDm200 to the aluminum box
No load or input
3) Using the thermal pad with adhesive (H48-6G-20-20-2.6-1A) and DO using thermal paste connecting the PDm200 to the aluminum box
No load or input

The tests showed the need of using the Thermal Pad but the use of Thermal Paste have not increase the dissipation capacity. A second test without thermal paste didn't have the same result, probable because the coupling between the 2 surfaces, a thicker thermal pad should solve this problem. The thermal pad data sheet shows that some pressure is necessary to obtain an optimal response.

06/01/2014
Redesign base PCB to fit 10cm long specification and reallocate components:
Base_PCB_3channel.SLDDRW
Design the Front and End plates:
K End Plate.SLDDRW
K Front Plate.SLDDRW
Board_2.SLDDRW

PDF versions saved here: https://drive.google.com/?tab=mo&authuser=0#folders/0B_KN6G919YgnTmRpNVQyYU1XR1U

10/12/2013 (1h7m)
search of components: BNC cable, piezo buzzer, thermal adhesive pad

R&D work on the Piezo Driver

Taken by Antonio
Work events:
Feb. 3, 2014 2.63 Time - Hours Done by Antonio

03/02/2014
3-Axis piezo driver assembled and working.
The driver is on operation with the piezo stack and the piezo tube for 1h for test. The metallic enclosure is warm, but just a little, nothing to be aware.
https://drive.google.com/file/d/0B_KN6G919YgnWXlmNGtPWnM1Vm8

31/01/2014
New components added to the part list.

30/01/2014
Re-assembling a 3-Axis driver using the new PCB and updating the part list with the missing components
https://docs.google.com/spreadsheet/ccc?key=0AvKN6G919YgndElQenVpbUZ6UTk1N0liYm4zbGRKbkE&usp=drive_web#gid=5

15/01/2014
Connectorizing the 3-axis piezo finger. Instructions here: https://docs.google.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY

Proceeding tests, The electronic system is working well, but the frequency limit is lower than we've supposed (about 25Hz using the filtered output, accordint to the datasheet we expect 3x this frequency using the non-filtered output).
The fiber is moving on the Z-axis, but we have a XY component working at the same time. I think this is due the bad quality of the actual mechanics and the non uniformity of the springs. I've also found a mistake at the top_base, it should the rotated by 45 degrees to be aligned with the XY-axis!

07/01/2014
Proceeding a heating test on the 3-axis PDm200: (https://docs.google.com/spreadsheet/ccc?key=0AvKN6G919YgndEEyamtKX1ZFU0Zkb1pIUTdFS2hybWc&usp=drive_web#gid=4)

1) no external dissipation, box closed, sensor on the black heat sink, measuring each 5min
2) Using the thermal pad with adhesive (H48-6G-20-20-2.6-1A) and NO thermal paste connecting the PDm200 to the aluminum box
No load or input
3) Using the thermal pad with adhesive (H48-6G-20-20-2.6-1A) and DO using thermal paste connecting the PDm200 to the aluminum box
No load or input

The tests showed the need of using the Thermal Pad but the use of Thermal Paste have not increase the dissipation capacity. A second test without thermal paste didn't have the same result, probable because the coupling between the 2 surfaces, a thicker thermal pad should solve this problem. The thermal pad data sheet shows that some pressure is necessary to obtain an optimal response.

06/01/2014
Redesign base PCB to fit 10cm long specification and reallocate components:
Base_PCB_3channel.SLDDRW
Design the Front and End plates:
K End Plate.SLDDRW
K Front Plate.SLDDRW
Board_2.SLDDRW

PDF versions saved here: https://drive.google.com/?tab=mo&authuser=0#folders/0B_KN6G919YgnTmRpNVQyYU1XR1U

10/12/2013 (1h7m)
search of components: BNC cable, piezo buzzer, thermal adhesive pad

R&D work on the Piezo Driver

Jan. 31, 2014 4.07 Time - Hours Done by Antonio

31/01/2014
New components added to the part list.

30/01/2014
Re-assembling a 3-Axis driver using the new PCB and updating the part list with the missing components
https://docs.google.com/spreadsheet/ccc?key=0AvKN6G919YgndElQenVpbUZ6UTk1N0liYm4zbGRKbkE&usp=drive_web#gid=5

15/01/2014
Connectorizing the 3-axis piezo finger. Instructions here: https://docs.google.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY

Proceeding tests, The electronic system is working well, but the frequency limit is lower than we've supposed (about 25Hz using the filtered output, accordint to the datasheet we expect 3x this frequency using the non-filtered output).
The fiber is moving on the Z-axis, but we have a XY component working at the same time. I think this is due the bad quality of the actual mechanics and the non uniformity of the springs. I've also found a mistake at the top_base, it should the rotated by 45 degrees to be aligned with the XY-axis!

07/01/2014
Proceeding a heating test on the 3-axis PDm200: (https://docs.google.com/spreadsheet/ccc?key=0AvKN6G919YgndEEyamtKX1ZFU0Zkb1pIUTdFS2hybWc&usp=drive_web#gid=4)

1) no external dissipation, box closed, sensor on the black heat sink, measuring each 5min
2) Using the thermal pad with adhesive (H48-6G-20-20-2.6-1A) and NO thermal paste connecting the PDm200 to the aluminum box
No load or input
3) Using the thermal pad with adhesive (H48-6G-20-20-2.6-1A) and DO using thermal paste connecting the PDm200 to the aluminum box
No load or input

The tests showed the need of using the Thermal Pad but the use of Thermal Paste have not increase the dissipation capacity. A second test without thermal paste didn't have the same result, probable because the coupling between the 2 surfaces, a thicker thermal pad should solve this problem. The thermal pad data sheet shows that some pressure is necessary to obtain an optimal response.

06/01/2014
Redesign base PCB to fit 10cm long specification and reallocate components:
Base_PCB_3channel.SLDDRW
Design the Front and End plates:
K End Plate.SLDDRW
K Front Plate.SLDDRW
Board_2.SLDDRW

PDF versions saved here: https://drive.google.com/?tab=mo&authuser=0#folders/0B_KN6G919YgnTmRpNVQyYU1XR1U

10/12/2013 (1h7m)
search of components: BNC cable, piezo buzzer, thermal adhesive pad

R&D work on the Piezo Driver

Jan. 30, 2014 4.08 Time - Hours Done by Antonio

30/01/2014
Re-assembling a 3-Axis driver using the new PCB

15/01/2014
Connectorizing the 3-axis piezo finger. Instructions here: https://docs.google.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY

Proceeding tests, The electronic system is working well, but the frequency limit is lower than we've supposed (about 25Hz using the filtered output, accordint to the datasheet we expect 3x this frequency using the non-filtered output).
The fiber is moving on the Z-axis, but we have a XY component working at the same time. I think this is due the bad quality of the actual mechanics and the non uniformity of the springs. I've also found a mistake at the top_base, it should the rotated by 45 degrees to be aligned with the XY-axis!

07/01/2014
Proceeding a heating test on the 3-axis PDm200: (https://docs.google.com/spreadsheet/ccc?key=0AvKN6G919YgndEEyamtKX1ZFU0Zkb1pIUTdFS2hybWc&usp=drive_web#gid=4)

1) no external dissipation, box closed, sensor on the black heat sink, measuring each 5min
2) Using the thermal pad with adhesive (H48-6G-20-20-2.6-1A) and NO thermal paste connecting the PDm200 to the aluminum box
No load or input
3) Using the thermal pad with adhesive (H48-6G-20-20-2.6-1A) and DO using thermal paste connecting the PDm200 to the aluminum box
No load or input

The tests showed the need of using the Thermal Pad but the use of Thermal Paste have not increase the dissipation capacity. A second test without thermal paste didn't have the same result, probable because the coupling between the 2 surfaces, a thicker thermal pad should solve this problem. The thermal pad data sheet shows that some pressure is necessary to obtain an optimal response.

06/01/2014
Redesign base PCB to fit 10cm long specification and reallocate components:
Base_PCB_3channel.SLDDRW
Design the Front and End plates:
K End Plate.SLDDRW
K Front Plate.SLDDRW
Board_2.SLDDRW

PDF versions saved here: https://drive.google.com/?tab=mo&authuser=0#folders/0B_KN6G919YgnTmRpNVQyYU1XR1U

10/12/2013 (1h7m)
search of components: BNC cable, piezo buzzer, thermal adhesive pad

R&D work on the Piezo Driver

Jan. 15, 2014 4.65 Time - Hours Done by Antonio

15/01/2014
Connectorizing the 3-axis piezo finger. Instructions here: https://docs.google.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY

Proceeding tests, The electronic system is working well, but the frequency limit is lower than we've supposed (about 25Hz using the filtered output, accordint to the datasheet we expect 3x this frequency using the non-filtered output).
The fiber is moving on the Z-axis, but we have a XY component working at the same time. I think this is due the bad quality of the actual mechanics and the non uniformity of the springs. I've also found a mistake at the top_base, it should the rotated by 45 degrees to be aligned with the XY-axis!

07/01/2014
Proceeding a heating test on the 3-axis PDm200: (https://docs.google.com/spreadsheet/ccc?key=0AvKN6G919YgndEEyamtKX1ZFU0Zkb1pIUTdFS2hybWc&usp=drive_web#gid=4)

1) no external dissipation, box closed, sensor on the black heat sink, measuring each 5min
2) Using the thermal pad with adhesive (H48-6G-20-20-2.6-1A) and NO thermal paste connecting the PDm200 to the aluminum box
No load or input
3) Using the thermal pad with adhesive (H48-6G-20-20-2.6-1A) and DO using thermal paste connecting the PDm200 to the aluminum box
No load or input

The tests showed the need of using the Thermal Pad but the use of Thermal Paste have not increase the dissipation capacity. A second test without thermal paste didn't have the same result, probable because the coupling between the 2 surfaces, a thicker thermal pad should solve this problem. The thermal pad data sheet shows that some pressure is necessary to obtain an optimal response.

06/01/2014
Redesign base PCB to fit 10cm long specification and reallocate components:
Base_PCB_3channel.SLDDRW
Design the Front and End plates:
K End Plate.SLDDRW
K Front Plate.SLDDRW
Board_2.SLDDRW

PDF versions saved here: https://drive.google.com/?tab=mo&authuser=0#folders/0B_KN6G919YgnTmRpNVQyYU1XR1U

10/12/2013 (1h7m)
search of components: BNC cable, piezo buzzer, thermal adhesive pad

R&D work on the Piezo Driver

Jan. 8, 2014 6.00 Time - Hours Done by Antonio

07/01/2014
Proceeding a heating test on the 3-axis PDm200: (https://docs.google.com/spreadsheet/ccc?key=0AvKN6G919YgndEEyamtKX1ZFU0Zkb1pIUTdFS2hybWc&usp=drive_web#gid=4)

1) no external dissipation, box closed, sensor on the black heat sink, measuring each 5min
2) Using the thermal pad with adhesive (H48-6G-20-20-2.6-1A) and NO thermal paste connecting the PDm200 to the aluminum box
No load or input
3) Using the thermal pad with adhesive (H48-6G-20-20-2.6-1A) and DO using thermal paste connecting the PDm200 to the aluminum box
No load or input

The tests showed the need of using the Thermal Pad but the use of Thermal Paste have not increase the dissipation capacity. A second test without thermal paste didn't have the same result, probable because the coupling between the 2 surfaces, a thicker thermal pad should solve this problem. The thermal pad data sheet shows that some pressure is necessary to obtain an optimal response.

06/01/2014
Redesign base PCB to fit 10cm long specification and reallocate components:
Base_PCB_3channel.SLDDRW
Design the Front and End plates:
K End Plate.SLDDRW
K Front Plate.SLDDRW
Board_2.SLDDRW

PDF versions saved here: https://drive.google.com/?tab=mo&authuser=0#folders/0B_KN6G919YgnTmRpNVQyYU1XR1U

10/12/2013 (1h7m)
search of components: BNC cable, piezo buzzer, thermal adhesive pad

R&D work on the Piezo Driver

Jan. 7, 2014 7.10 Time - Hours Done by Antonio

07/01/2014
Proceeding a heating test on the 3-axis PDm200: (https://docs.google.com/spreadsheet/ccc?key=0AvKN6G919YgndEEyamtKX1ZFU0Zkb1pIUTdFS2hybWc&usp=drive_web#gid=4)

1) no external dissipation, box closed, sensor on the black heat sink, measuring each 5min
2) Using the thermal pad with adhesive (H48-6G-20-20-2.6-1A) and NO thermal paste connecting the PDm200 to the aluminum box
No load or input
3) Using the thermal pad with adhesive (H48-6G-20-20-2.6-1A) and DO using thermal paste connecting the PDm200 to the aluminum box
No load or input

The tests showed the need of using the Thermal Pad but the use of Thermal Paste have not increase the dissipation capacity. A second test without thermal paste didn't have the same result, probable because the coupling between the 2 surfaces, a thicker thermal pad should solve this problem. The thermal pad data sheet shows that some pressure is necessary to obtain an optimal response.

06/01/2014
Redesign base PCB to fit 10cm long specification and reallocate components:
Base_PCB_3channel.SLDDRW
Design the Front and End plates:
K End Plate.SLDDRW
K Front Plate.SLDDRW
Board_2.SLDDRW

PDF versions saved here: https://drive.google.com/?tab=mo&authuser=0#folders/0B_KN6G919YgnTmRpNVQyYU1XR1U

10/12/2013 (1h7m)
search of components: BNC cable, piezo buzzer, thermal adhesive pad

R&D work on the Piezo Driver

Jan. 6, 2014 2.20 Time - Hours Done by Antonio

06/01/2014
Redesign base PCB to fit 10cm long specification and reallocate components:
Base_PCB_3channel.SLDDRW
Design the Front and End plates:
K End Plate.SLDDRW
K Front Plate.SLDDRW
Board_2.SLDDRW

PDF versions saved here: https://drive.google.com/?tab=mo&authuser=0#folders/0B_KN6G919YgnTmRpNVQyYU1XR1U

10/12/2013 (1h7m)
search of components: BNC cable, piezo buzzer, thermal adhesive pad

R&D work on the Piezo Driver

Dec. 10, 2013 1.12 Time - Hours Done by Antonio

10/12/2013 (1h7m)
search of components: BNC cable, piezo buzzer, thermal adhesive pad

R&D work on the Piezo Driver

Nov. 25, 2013 15.00 Time - Hours Done by Antonio

2-Channel sale (Brian)
Work from 25/11 - 28/11
Callibration
Assembly Instructions
Production test (http://goo.gl/LUSxgL)
R&D test (rise and fall time) http://goo.gl/W5Lke0

Nov. 15, 2013 12.00 Time - Hours Done by Antonio

Work from 15/11 - 20/11
3-Axis Tests
Documenting BOM
Component searching, buying
https://docs.google.com/spreadsheet/ccc?key=0AvKN6G919YgndElQenVpbUZ6UTk1N0liYm4zbGRKbkE&usp=sharing

Oct. 23, 2013 5.00 Time - Hours Done by Antonio

3-Channel electronics and 3D design

Oct. 22, 2013 3.50 Time - Hours Done by Antonio

3-Channel electronic design

Sept. 24, 2013 4.00 Time - Hours Done by Antonio

Search and buy components

Sept. 17, 2013 7.50 Time - Hours Done by Antonio

2-channel electronic driver final version designing

Sept. 16, 2013 4.00 Time - Hours Done by Antonio

2-channel electronic driver final version designing

Sept. 13, 2013 4.00 Time - Hours Done by Antonio

2-channel final version designing

Sept. 11, 2013 5.00 Time - Hours Done by Antonio

2-channel final version designing

Sept. 10, 2013 7.00 Time - Hours Done by Antonio

2-channel final version designing

Aug. 30, 2013 4.00 Time - Hours Done by Antonio

Documentation of the 2-channel piezo driver
Finishing prototype and testing 2-channel piezo driver
Test with the piezo at different conditions (up to 1Khz @ 100V)
https://docs.google.com/document/d/1zwBYykbxaoEmqh89vuBCs7lXBgTlB1Ien-oQkI6DVvE/edit#

Aug. 29, 2013 1.00 Time - Hours Done by Antonio
Aug. 28, 2013 6.50 Time - Hours Done by Antonio

Electronic design
Mechanical and electronic assembling the first prototype
https://docs.google.com/document/d/1zwBYykbxaoEmqh89vuBCs7lXBgTlB1Ien-oQkI6DVvE/edit#

Aug. 27, 2013 9.00 Time - Hours Done by Antonio

Testing and designing the application for the PDu100
Assembling the first prototype
https://docs.google.com/document/d/1yTmagtJU5iRpw-zIXzSsBb3SujSnGLRnoUmadPqTXrs/edit

Aug. 23, 2013 4.50 Time - Hours Done by Antonio

Studying and electronic designing PDu100 piezo driver
Buy components to the prototype
https://docs.google.com/document/d/1yTmagtJU5iRpw-zIXzSsBb3SujSnGLRnoUmadPqTXrs/edit

Aug. 22, 2013 4.00 Time - Hours Done by Antonio

Prototyping the application of PDm200 driver.
Driver working at 24V delivering up to +200V / -20V at unipolar mode
The driver also can work at +200V/-200V at bipolar mode
https://docs.google.com/document/d/1zwBYykbxaoEmqh89vuBCs7lXBgTlB1Ien-oQkI6DVvE/edit

Aug. 21, 2013 4.00 Time - Hours Done by Antonio
Aug. 20, 2013 4.50 Time - Hours Done by Antonio
R&d electronics work: 20.00 Time - Hours due Jan. 4, 2014

Jonathan
1/13/2014
panelizing pcbs and making order

1/10/2014
regenerating gerbers with separate slot drill file

1/9/2014
Finalized pcb and generated gerber files and drill files.
1/8/2014
base board rev2 is now finished, silk overlay is finished

1/7/2014 modifying Piezo Drive Module Integration base board - rev 2 which can be found here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board - rev2\Piezo Drive Module Integration base board - rev 2.PrjPcb
I am adjusting the pcb to match the dimensions given by antonio in this document:

Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15
pcb piezo prototype 3h20
pcb piezo prototype 1h
etching piezo prototype 5h
soldering piezo 6h30

Taken by Jonathan
Work events:
Jan. 13, 2014 1.13 Time - Hours Done by Jonathan

Jonathan
1/13/2014
panelizing pcbs and making order

1/10/2014
regenerating gerbers with separate slot drill file

1/9/2014
Finalized pcb and generated gerber files and drill files.
1/8/2014
base board rev2 is now finished, silk overlay is finished

1/7/2014 modifying Piezo Drive Module Integration base board - rev 2 which can be found here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board - rev2\Piezo Drive Module Integration base board - rev 2.PrjPcb
I am adjusting the pcb to match the dimensions given by antonio in this document:

Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15
pcb piezo prototype 3h20
pcb piezo prototype 1h
etching piezo prototype 5h
soldering piezo 6h30

Jan. 11, 2014 0.00 Time - Hours Done by Jonathan

Jonathan
1/10/2014
regenerating gerbers with separate slot drill file

1/9/2014
Finalized pcb and generated gerber files and drill files.
1/8/2014
base board rev2 is now finished, silk overlay is finished

1/7/2014 modifying Piezo Drive Module Integration base board - rev 2 which can be found here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board - rev2\Piezo Drive Module Integration base board - rev 2.PrjPcb
I am adjusting the pcb to match the dimensions given by antonio in this document:

Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15
pcb piezo prototype 3h20
pcb piezo prototype 1h
etching piezo prototype 5h
soldering piezo 6h30

Jan. 11, 2014 5.20 Time - Hours Done by Jonathan

Jonathan
1/10/2014
regenerating gerbers with separate slot drill file

1/9/2014
Finalized pcb and generated gerber files and drill files.
1/8/2014
base board rev2 is now finished, silk overlay is finished

1/7/2014 modifying Piezo Drive Module Integration base board - rev 2 which can be found here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board - rev2\Piezo Drive Module Integration base board - rev 2.PrjPcb
I am adjusting the pcb to match the dimensions given by antonio in this document:

Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15
pcb piezo prototype 3h20
pcb piezo prototype 1h
etching piezo prototype 5h
soldering piezo 6h30

Jan. 10, 2014 11.07 Time - Hours Done by Jonathan

Jonathan
1/10/2014
regenerating gerbers with separate slot drill file

1/9/2014
Finalized pcb and generated gerber files and drill files.
1/8/2014
base board rev2 is now finished, silk overlay is finished

1/7/2014 modifying Piezo Drive Module Integration base board - rev 2 which can be found here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board - rev2\Piezo Drive Module Integration base board - rev 2.PrjPcb
I am adjusting the pcb to match the dimensions given by antonio in this document:

Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15
pcb piezo prototype 3h20
pcb piezo prototype 1h
etching piezo prototype 5h
soldering piezo 6h30

Jan. 10, 2014 0.02 Time - Hours Done by Jonathan

Jonathan
1/10/2014
regenerating gerbers with seperate slot drill file

1/9/2014
Finalized pcb and generated gerber files and drill files.
1/8/2014
base board rev2 is now finished, silk overlay is finished

1/7/2014 modifying Piezo Drive Module Integration base board - rev 2 which can be found here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board - rev2\Piezo Drive Module Integration base board - rev 2.PrjPcb
I am adjusting the pcb to match the dimensions given by antonio in this document:

Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15
pcb piezo prototype 3h20
pcb piezo prototype 1h
etching piezo prototype 5h
soldering piezo 6h30

Jan. 9, 2014 8.38 Time - Hours Done by Jonathan

Jonathan
1/8/2014
base board rev2 is now finished, silk overlay is finished
1/9/2014
Finalized pcb and generated gerber files and drill files.

1/7/2014 modifying Piezo Drive Module Integration base board - rev 2 which can be found here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board - rev2\Piezo Drive Module Integration base board - rev 2.PrjPcb
I am adjusting the pcb to match the dimensions given by antonio in this document:

Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15
pcb piezo prototype 3h20
pcb piezo prototype 1h
etching piezo prototype 5h
soldering piezo 6h30

Jan. 8, 2014 6.88 Time - Hours Done by Jonathan

Jonathan
1/8/2014
base board rev2 is now finished, currently I am finalizing the silk overlay.

1/7/2014 modifying Piezo Drive Module Integration base board - rev 2 which can be found here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board - rev2\Piezo Drive Module Integration base board - rev 2.PrjPcb
I am adjusting the pcb to match the dimensions given by antonio in this document:

Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15
pcb piezo prototype 3h20
pcb piezo prototype 1h
etching piezo prototype 5h
soldering piezo 6h30

Jan. 8, 2014 0.00 Time - Hours Done by Jonathan

Jonathan
1/8/2014
base board rev2 is now finished, currently I am finalizing the silk overlay.

1/7/2014 modifying Piezo Drive Module Integration base board - rev 2 which can be found here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board - rev2\Piezo Drive Module Integration base board - rev 2.PrjPcb
I am adjusting the pcb to match the dimensions given by antonio in this document:

Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15
pcb piezo prototype 3h20
pcb piezo prototype 1h
etching piezo prototype 5h
soldering piezo 6h30

Jan. 7, 2014 6.05 Time - Hours Done by Jonathan

Jonathan

1/7/2014 modifying Piezo Drive Module Integration base board - rev 2 which can be found here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board - rev2\Piezo Drive Module Integration base board - rev 2.PrjPcb
I am adjusting the pcb to match the dimensions given by antonio in this document:

Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15
pcb piezo prototype 3h20
pcb piezo prototype 1h
etching piezo prototype 5h
soldering piezo 6h30

Oct. 30, 2013 2.83 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Oct. 29, 2013 0.00 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Oct. 26, 2013 2.00 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Oct. 24, 2013 3.75 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Oct. 23, 2013 4.17 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Oct. 22, 2013 4.75 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Oct. 21, 2013 3.58 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Oct. 18, 2013 1.18 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Oct. 17, 2013 8.00 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Oct. 16, 2013 4.50 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Oct. 11, 2013 3.00 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Oct. 10, 2013 0.00 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Oct. 4, 2013 8.42 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Oct. 2, 2013 3.50 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration
Designing OUT board pcb 3h30
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Sept. 30, 2013 3.50 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Sept. 25, 2013 6.00 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Sept. 23, 2013 4.50 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Sept. 18, 2013 3.42 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Sept. 17, 2013 7.83 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Sept. 13, 2013 4.83 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Sept. 12, 2013 2.87 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration
Piezo Module PCB Layout
Piezo Module PCB Layout
Piezo Module PCB Layout
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Sept. 11, 2013 4.50 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration
Piezo Module PCB Layout
Piezo Module PCB Layout
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Sept. 10, 2013 6.08 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration
Piezo Module PCB Layout
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

Sept. 9, 2013 0.67 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration
Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

July 25, 2013 6.50 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15
pcb piezo prototype 3h20
pcb piezo prototype 1h
etching piezo prototype 5h
soldering piezo 6h30

July 24, 2013 6.00 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15
pcb piezo prototype 3h20
pcb piezo prototype 1h
etching piezo prototype 5h

July 23, 2013 3.33 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15
pcb piezo prototype 3h20

July 22, 2013 5.25 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15

July 19, 2013 6.00 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h

July 18, 2013 0.00 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m
piezo assembly 4h40
testing piezo 6h
piezo debugging 5h15
pcb piezo prototype 3h20
pcb piezo prototype 1h
etching piezo prototype 5h

July 17, 2013 1.33 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40
Working on the interface for the piezo 1h
pcb payout for adapter board 20m

July 8, 2013 1.67 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration

Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20
piezo bom 3h20
pcb search and order 1h40

July 5, 2013 8.33 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration
Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45
piezo box shopping, final piezo layout 8h20

July 4, 2013 7.75 Time - Hours Done by Jonathan

Jonathan
Piezo Driver Connector search, quoted PDu100 modules from american supplier 1.5hrs
Piezo PCB and component search 10h55mins ~11h

Piezo PCB still on being worked on. Today spent 3hrs and will press start button now.

See pcb here:
\Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration
Piezo Module PCB Layout 40m
Piezo Module PCB Layout 6h05
Piezo Module PCB Layout 4h30
Piezo Module PCB Layout 2h52
Piezo Module PCB Layout 4h50
Piezo Module PCB Layout 4h30
piezo pdm200 testing, sent po for linear stage 7h50
Piezo Module PCB layout + meeting 3h25
Piezo Clean up (sorted all the accumulated parts, sorted work spaces etc) 4h30
Piezo Module PCB layout 3h45
Baseboard PCB layout 6h
Baseboard PCB layout 2h
Piezo 2ch Assembly 2h50
3Ch piezo final design review, start soldering 2ch piezo 3h30
Designing OUT board pcb 3h30
See it here \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration OUT board
Designing PCB 8h25
Testing 3 Ch Piezo and designing PCB 5h18
Designing 3ch PCB 3h
see it here: \Dropbox\tactus\piezo system\PCB - rev 4 - Piezo Drive Module integration base board
Patterning and Etching PCBs for 3Ch board and 2ch out board 8h
Cutting PCBs 45m
PCB Assembly 26m
Assembling Piezo PCBs 26m
Above three items are for the home made pcbs, the out board and the base board, for the 3 ch device
Assembling Piezo PCBs 3h35
Recording the time it takes to assemble piezo pcbs 4h45
see document here: https://docs.google.com/a/olesik.com/document/d/1qGbzFsd7eTMJ2wGnYq7mnx2ik7y9CZoJWg2onIih7BY/edit
Ordering Piezo Parts (for extra units) 4h10

This is for the Piezo Prototypes created by F.Cantin
piezo bom and layout 5h
piezo layout 7h45

Unplanned Work:

Work event: Technician experimental work 2.00 Time - Hours Nov. 13, 2013 Done by Tibi

testing the piezo actuator and driver using LabView program and a laser pointer. Worked with Francois.

Work event: Technician experimental work 5.00 Time - Hours Sept. 25, 2013 Done by Antonio

Installation and tests of the the 2-channels piezo driver at Philip's Lab

Work event: R&d mechanics work 6.00 Time - Hours Sept. 23, 2013 Done by Antonio

Designing mechanics using SolidWorks

Work event: R&d mechanics work 4.00 Time - Hours Sept. 20, 2013 Done by Antonio

Design mechanics assembling

Work event: Technician experimental work 4.50 Time - Hours Sept. 4, 2013 Done by Antonio

Installation of the the 2-channels piezo driver at Dilsons Lab

Citations

Unplanned Citations:

Cited: Piezo_LJ-1ax-v2 1.00 Time - Hours Nov. 14, 2013

Usable Inputs

Tool - thermocouple: 6.00 Time - Hours due Nov. 12, 2013

07/01/2014
Using the thermocouple to test the efficiency of the Thermal PAD with adhesive (H48-6G-20-2.6-1A)

Unplanned Use:

Used: Power supply: Power supply GQ 2.00 Time - Hours Nov. 13, 2013

Process context:

Pattern: Generic R&D
Context: Manipulators
Order: Work order 101 for piezo order due: 2014-04-28

Previous processes:

Make LabView program for 1 axis piezo starting 2013-11-01 ending 2013-11-02

Next processes:

Make Brochure for piezo Mantis specs to piezo order starting 2013-09-10 ending 2013-11-01


Process notes:

PCBs arrive Monday Sept 30. Tuesday, soldering. Friday October 4, 5 electronics box can be ready.
October 4: 2-axis is done
1 axis and 3 axis are coming soon (next week)

Friday October 18: 2 and 3 channels are ready today.
Friday October 25: some parts are still missing. New due date is Nov 1st.
To deliver: 2 x 2 axis, 2 x 3 axis